OSSIM STUFF ON PG 17! Worklog: The TriSixtyFource
- Thread starter ShockSlayer
- Start date
ShockSlayer
Probably SS
Re: Worklog: The TriSixtyFource
Doing it the way I am doing it gives me a way to exploit the n64 board and not RCP relocate. Which I am trying to avoid. Remember, I have two cases. I'll go for smallest once I get a couple more n64 mobo's and some ram.
SS
Doing it the way I am doing it gives me a way to exploit the n64 board and not RCP relocate. Which I am trying to avoid. Remember, I have two cases. I'll go for smallest once I get a couple more n64 mobo's and some ram.
SS
snowpenguin
Frequent Poster
Re: Worklog: The TriSixtyFource
He's going to use the extra width the controller provides to make it so the n64 board will fit.
He's going to use the extra width the controller provides to make it so the n64 board will fit.
ToastBucket
tost
Re: Worklog: The TriSixtyFource
Nice zet.......
Is that ABS, SS? You probably mentioned when you showed the picture but that's like a page away.
Nice zet.......
Is that ABS, SS? You probably mentioned when you showed the picture but that's like a page away.
Basement_Modder
He who mods in thy basement.
Re: Worklog: The TriSixtyFource
Nice "exploit."
Now the top half of the main case can be nothing but batteries!
(and screen.)
Nice "exploit."
Now the top half of the main case can be nothing but batteries!
(and screen.)
if both hands were at the same angle I'd use it 
ShockSlayer
Probably SS
Re: Worklog: The TriSixtyFource
Both back's on. It takes a night for this JB Weld to cure so it'll take me two more days to put the other two halfs on. XD
The mobo just barely fits, it's going to take a little rewiring in certain parts but otherwise it's good.
I plan to include a LOB64 port, a headphone jack and an exp port if I can find room.
SS
Both back's on. It takes a night for this JB Weld to cure so it'll take me two more days to put the other two halfs on. XD
The mobo just barely fits, it's going to take a little rewiring in certain parts but otherwise it's good.
I plan to include a LOB64 port, a headphone jack and an exp port if I can find room.
SS
ShockSlayer
Probably SS
Re: Worklog: The TriSixtyFource
I'm not5 RCP wiring. THat's the whole point of controller flanks, extending the case and providing that good feel.
On that note, I still need to fill in some gaps, I'll do that later. Pics.....tomorrow. Tomorrow is my birthday!
SS
I'm not5 RCP wiring. THat's the whole point of controller flanks, extending the case and providing that good feel.
On that note, I still need to fill in some gaps, I'll do that later. Pics.....tomorrow. Tomorrow is my birthday!
SS
Argelfraster
Well-Known Member
Re: Worklog: The TriSixtyFource
He said he wont do an RCP wired cart slot, and there are no capacitors on the board, so that board is probably just for measuring.Jidan said:It looks like you have the cart slot area cut off to me. Or is that not gonna be in the actual N64?
samjc3
#1 Female Member
Re: Worklog: The TriSixtyFource
also notice the writing all over it. weve seen that board before.Argelfraster said:He said he wont do an RCP wired cart slot, and there are no capacitors on the board, so that board is probably just for measuring.Jidan said:
ShockSlayer
Probably SS
Re: Worklog: The TriSixtyFource
Yep it's a dead board I use for sizing. XD THis is the one with the bad 7805, then I stole a couple caps from it. XD
SS
Yep it's a dead board I use for sizing. XD THis is the one with the bad 7805, then I stole a couple caps from it. XD
SS
