The MCp (MoRZi-CUBE Portable) My Gamecube Portable(Canceled)
- Thread starter MoRZiLLo
- Start date
superben51
Well-Known Member
Re: The MCp (MoRZi-CUBE Portable) My Gamecube Portable Workl
Check out bentomo's controller scans to see if you can scrape away some paint/mobo to show the trace. If you feeling brave then you could try soldering right to the chip as well using the pinout in the mega-sticky.
Check out bentomo's controller scans to see if you can scrape away some paint/mobo to show the trace. If you feeling brave then you could try soldering right to the chip as well using the pinout in the mega-sticky.
MoRZiLLo
Active Member
Re: The MCp (MoRZi-CUBE Portable) My Gamecube Portable Workl
Thanks but the bentomo scans is for unoficial controllers or compatibles.
I have the original nintendo controllers. And the points nowhere in the board.
Tomorrow i will try the last fix and if i can find a way to resolve this, can continue my project.
If i has no luck, i will destroy my MCp
No no... but i'm waiting for money to buy new hardware and re-done all stuff in controller parts.
Thanks for the answer
Thanks but the bentomo scans is for unoficial controllers or compatibles.
I have the original nintendo controllers. And the points nowhere in the board.
Tomorrow i will try the last fix and if i can find a way to resolve this, can continue my project.
If i has no luck, i will destroy my MCp
No no... but i'm waiting for money to buy new hardware and re-done all stuff in controller parts.
Thanks for the answer
Joeyjoe9876
Frequent Poster
Re: The MCp (MoRZi-CUBE Portable) My Gamecube Portable Workl
scrape away the paint and try to look for the trace. I accidentally did this to one of my boards and ended up just soldering to a transistor.
scrape away the paint and try to look for the trace. I accidentally did this to one of my boards and ended up just soldering to a transistor.
MoRZiLLo
Active Member
Re: The MCp (MoRZi-CUBE Portable) My Gamecube Portable Workl
Well!!! I sanded manually a piece of controller and discover posible relocations.
NOTE THAT IS NOT CORRECT COLORS!!!!!! Only for distinct relocations points.
If i can run my controller again with this relocation, i'm very veryyyyy happy!!
Bottom of Controller
Top of Controller
Relocations?? I sanded more than need in this two grey points
Images from my cam are 4mb and very huuuuuuuuuuugeeeee
When i soldered to the points, post here if run or not.
Thanks for the help!
NOTE: This scans are different from bentomo's scans. The bentomo's is for the (blue bean thing in the center) other oficial controller. Mine is a plated elipsed thing. like this
Well!!! I sanded manually a piece of controller and discover posible relocations.
NOTE THAT IS NOT CORRECT COLORS!!!!!! Only for distinct relocations points.
If i can run my controller again with this relocation, i'm very veryyyyy happy!!
Bottom of Controller
Top of Controller
Relocations?? I sanded more than need in this two grey points
Images from my cam are 4mb and very huuuuuuuuuuugeeeee
When i soldered to the points, post here if run or not.
Thanks for the help!
NOTE: This scans are different from bentomo's scans. The bentomo's is for the (blue bean thing in the center) other oficial controller. Mine is a plated elipsed thing. like this
superben51
Well-Known Member
Re: The MCp (MoRZi-CUBE Portable) My Gamecube Portable Workl
I'm pretty sure that those to two points there are ground, so any ground spot on the controller will do.
I'm pretty sure that those to two points there are ground, so any ground spot on the controller will do.
MoRZiLLo
Active Member
Re: The MCp (MoRZi-CUBE Portable) My Gamecube Portable Workl
YEAH!!!!!!
If i sleep a little, when i wakeup in morning, solder to the alternative points and try if the relocation works.
Thanks superben51!!!
I found a best batery pack ever seen before!!!!!
Is a 20.000mAh 12v~14v~19V
For laptop PCs and more
120.46$ but is reasonable for the power!!!
HERE is the link.
I can't buy this huge batery pack, but is a good option for people with laptops, notebooks and powering anything.
YEAH!!!!!!
If i sleep a little, when i wakeup in morning, solder to the alternative points and try if the relocation works.
Thanks superben51!!!
I found a best batery pack ever seen before!!!!!
Is a 20.000mAh 12v~14v~19V
For laptop PCs and more
120.46$ but is reasonable for the power!!!
HERE is the link.
I can't buy this huge batery pack, but is a good option for people with laptops, notebooks and powering anything.
MoRZiLLo
Active Member
Re: The MCp (MoRZi-CUBE Portable) My Gamecube Portable Workl
OK new discovering tales... xD
This pic is really crappy, i'm suck at paint a lot.
Blue is 3.43v - PIN 1
Yellow is +5v - PIN 2
Red is Dataline - PIN 3
Green is Ground - PIN 4
White is Groung - PIN 5
Black is cable shielding(ground too) - PIN 6
The broken pins can't relocating is 3.43v logic supply and +5v in for rumble motor?
If only 3.43v can relocate to the chip on controller it runs!!!!
Rumble is not necesary for me. I can put directly from motherboard to the circuit of rumble if needed.
This weekend i'll try to fix the controller....
OK new discovering tales... xD
This pic is really crappy, i'm suck at paint a lot.
Blue is 3.43v - PIN 1
Yellow is +5v - PIN 2
Red is Dataline - PIN 3
Green is Ground - PIN 4
White is Groung - PIN 5
Black is cable shielding(ground too) - PIN 6
The broken pins can't relocating is 3.43v logic supply and +5v in for rumble motor?
If only 3.43v can relocate to the chip on controller it runs!!!!
Rumble is not necesary for me. I can put directly from motherboard to the circuit of rumble if needed.
This weekend i'll try to fix the controller....
MoRZiLLo
Active Member
Re: The MCp (MoRZi-CUBE Portable) My Gamecube Portable Workl
Ohhhh men!!!!!! IT WORKS!!!!!!!
But......something wrong sometimes.
Maybe large wires and a short in between the buttons or gnd or something...
But works again
I'll try to fix later, my neck is broken in half hehehehe(teorically
)
Ohhhh men!!!!!! IT WORKS!!!!!!!
But......something wrong sometimes.
Maybe large wires and a short in between the buttons or gnd or something...
But works again
I'll try to fix later, my neck is broken in half hehehehe(teorically
)
lyberty5
Well-Known Member
Re: The MCp (MoRZi-CUBE Portable) My Gamecube Portable Workl
dude.. you know you can use a multimeter instead of sanding a controller.
Also if you read ashen's guide you'd have had direct relocation points to the chip.
I mean, this exact thing happenned to me before, it is supposed to be a really easy fix
Good for you if you finally made it work anyway.
dude.. you know you can use a multimeter instead of sanding a controller.
Also if you read ashen's guide you'd have had direct relocation points to the chip.
I mean, this exact thing happenned to me before, it is supposed to be a really easy fix
Good for you if you finally made it work anyway.
MoRZiLLo
Active Member
Re: The MCp (MoRZi-CUBE Portable) My Gamecube Portable Workl
It's difficult to put wires in the chip!!!!!
I'm not capable of solder in a megatiny points without bridge them xD
Anyway, something is wrong.
I need new controller.
Merçi pour le help!
Ahhh And sanding a controller is no problem for me, i have two broken here
It's difficult to put wires in the chip!!!!!
I'm not capable of solder in a megatiny points without bridge them xD
Anyway, something is wrong.
I need new controller.
Merçi pour le help!
Ahhh And sanding a controller is no problem for me, i have two broken here
MoRZiLLo
Active Member
Re: The MCp (MoRZi-CUBE Portable) My Gamecube Portable Workl
Nope. If i bridge the 3 pins,(two ground and shielded) the controller does anything. If unbridge and solder separately it runs, but with some problems.
I think the problem is a longgggggggg wires and from buttons is "fat wire" and in the solder points a "thin wire" merged both in one 40cm long wire xD
Nope. If i bridge the 3 pins,(two ground and shielded) the controller does anything. If unbridge and solder separately it runs, but with some problems.
I think the problem is a longgggggggg wires and from buttons is "fat wire" and in the solder points a "thin wire" merged both in one 40cm long wire xD
thecasperrojas
Well-Known Member
Re: The MCp (MoRZi-CUBE Portable) My Gamecube Portable Workl
mira q tu quieres aser en si con lo del control bro y sabes si necesitas ayuda con el wiikey me avisas
mira q tu quieres aser en si con lo del control bro y sabes si necesitas ayuda con el wiikey me avisas
Gamerlolwind
Well-Known Member
Re: The MCp (MoRZi-CUBE Portable) My Gamecube Portable(Cance
Oh!
Why's the project canceled, Morzillo??
Did something happen to your portable??
What will you do with the canceled portable?
MoRZiLLo said:
Oh!
Why's the project canceled, Morzillo??
Did something happen to your portable??
What will you do with the canceled portable?
MoRZiLLo
Active Member
Re: The MCp (MoRZi-CUBE Portable) My Gamecube Portable(Cance
I'm not capable of doing
I'll made all into my posibility, can't do anymore and can't finish alone.
But someday when my skills better.....i don't know if continue, but for the moment, it's all can be done.
Sorry!
I'm not capable of doing
I'll made all into my posibility, can't do anymore and can't finish alone.
But someday when my skills better.....i don't know if continue, but for the moment, it's all can be done.
Sorry!
thecasperrojas
Well-Known Member
Re: The MCp (MoRZi-CUBE Portable) My Gamecube Portable(Cance
de ninguna manera vas a cancelar esta bellesa pm's a mi haora >;( q t falta me dises por pm's
de ninguna manera vas a cancelar esta bellesa pm's a mi haora >;( q t falta me dises por pm's
