Wiikey Fusion Problem

PRXVII · **Joined:** Tue Jan 03, 2012 6:55 pm **Posts:** 53

Dang. I was able to load up Swiss and confirmed that it is in fact a 1.0.

PRXVII · **Joined:** Tue Jan 03, 2012 6:55 pm **Posts:** 53

I tried it on my second GC and it's also a v1.0. So disappointing. Does anyone have a >v1.0 Rev A/B board for sale?

PRXVII · **Joined:** Tue Jan 03, 2012 6:55 pm **Posts:** 53

More problems >:(

. I finally got a Rev. B IPLv1.1 board and wired up the WKF. I can get to the WKF menu fine, but when I start a game I get the error "An error has occurred. Turn the power off and refer to the Nintendo Gamecube Instruction Booklet for further instructions." after a few seconds. I tried SSX: On Tour, SSBM, and Metroid Prime. First two games I only tried like twice, but Metroid Prime I kept attempting. Usually the error would come up after the Nintendo logo. Sometimes it would get past the Nintendo, Retro Studios, and Dolby Audio logos, after a black screen with the background sounds playing then I'd get the error. The last time I tried I was able to get to the menu and start the game, I saw the first lines of text and then got the error. Any ideas?

Ashen · **Posted:** Thu Jan 26, 2012 11:56 pm

Sounds like you've got a bad connection somewhere or maybe latency issues. I'd recheck all of your solder joints. How long are your wires? Region switch set correctly?

Mr. Hooker · **Posted:** Fri Jan 27, 2012 5:07 am

check the ribbin going to the sd socket. doe's it need to be fliped, is there a hard crease or fold in the ribbin.

PRXVII · **Joined:** Tue Jan 03, 2012 6:55 pm **Posts:** 53

Ashen wrote:

Sounds like you've got a bad connection somewhere or maybe latency issues. I'd recheck all of your solder joints. How long are your wires? Region switch set correctly?

All the joints looked fine, but to make sure I desoldered and resoldered every connection and the error persists. My wires are 4" and the region switch is set correctly.

Mr. Hooker wrote:

check the ribbin going to the sd socket. doe's it need to be fliped, is there a hard crease or fold in the ribbin.

I reconnected both ends of the sd ribbon but it didn't change anything. And there are no creases/folds in the cable.

SonyQrio · **Posted:** Fri Jan 27, 2012 8:00 pm

Maybe it's the class of your SD card. If you have a higher class card, then give it a try.

PRXVII · **Joined:** Tue Jan 03, 2012 6:55 pm **Posts:** 53

SonyQrio wrote:

Maybe it's the class of your SD card. If you have a higher class card, then give it a try.

I'm using an old Kingston 2GB with no class marking so it's most likely a Class 2. I thought this might be it but I don't have another card to test. I'll have to buy one. Is Class 10 overkill? Does it make game loading noticeably faster?

SonyQrio · **Posted:** Fri Jan 27, 2012 9:49 pm

PRXVII wrote:

I'm using an old Kingston 2GB with no class marking so it's most likely a Class 2. I thought this might be it but I don't have another card to test. I'll have to buy one. Is Class 10 overkill? Does it make game loading noticeably faster?

Yeah, that's probably it. Getting a class 10 is definitely a good investment to make.

Ashen · **Posted:** Fri Jan 27, 2012 10:21 pm

If you soldered directly to the FFC I'd recheck connections through the FFC first before I invested in another SD card. All the cards I have are like class 4-6 and work fine.

Wiikey Fusion Problem

Who is online